Automatic Door Sensor
Embedded-Type Sensor
Ultra-compact sensor [SP201]
A composite sensor that combines a detection sensor with a safety sensor
Key features
– Perfect side-entry detection
– Top flush-mounted design (controller integrated)
– Immune to environmental interference (sunlight/lighting/vibration)
– Blind spot-free motion detection safety sensor
– Adjustable external detection range via sliding sensor window while maintaining inner zone integrity
| Specifications | |||||
|---|---|---|---|---|---|
|
Detection method |
Far-infrared source |
||||
|
nstallation height |
Below 3m |
||||
|
Detection range |
Left/Right |
1.2m[of the centerline]@ Height of 2.2m |
|||
|
Front/Rear |
0.1m – (0.5~1.2)m @ Height of 2.2m |
||||
|
Normal |
DC 12V ~ 30V
※ The input voltage must be 12V or higher |
||||
|
Consumption power |
240mW(12V, 20mA or less) |
||||
|
Temperature |
In storage |
-40℃ ~ 85℃ |
|||
|
In use |
-25℃ ~ 50℃ |
||||
|
Humidity |
35% ~ 85% RH |
||||
|
Weight |
Max. 25g |
||||
|
Electrical wiring |
Grey[Power supply] and Yellow[Relay output] |
||||
※ Initial stabilization time: 10 seconds
※ These specifications may be changed without any prior notice.
※ The detection range may vary depending on the installation environment or conditions
External Appearance
1. Drill 30Φ hole at the bottom of the engine box
Locate hole position away from moving door parts
2, Insert sensor connection cable
3. Connect to controller
4, Attach sensor connector
5. Mount sensor panel
Align panel grooves parallel to glass door
Ensure panel surface is perpendicular to door & parallel to floor
Use double-sided tape if needed
Configuration
① Door Direction
② Detection Area Adjustment (Inner): Inner Zone Adjustment Window
③ Sensitivity Level Display
-1 (Lowest Sensitivity)
-5 (Highest Sensitivity)
④ Sensitivity Adjustment: Clockwise Rotation (Increase Sensitivity)
⑤ Detection Area Adjustment (Outer): Outer Zone Adjustment Window
Dedicated safety sensor[SP101]
For environments with existing automatic door sensors, this dedicated safety sensor can be easily installed as an additional safety measure.
Key Features
– Simplified installation process for safety beam sensors (eliminates complexity)
– Top flush-mounted design (integrated controller)
– Immune to false triggers from sunlight, ambient lighting, or vibrations
– Blind spot-free motion detection safety sensor
| Specifications | |||||
|---|---|---|---|---|---|
|
Detection method |
Far-infrared source |
||||
|
nstallation height |
Below 3m |
||||
|
Detection range |
Left/Right |
1.2m[of the centerline]@ Height of 2.2m |
|||
|
Front/Rear |
0.1m – (0.5~1.2)m @ Height of 2.2m |
||||
|
Normal |
DC 12V ~ 30V ※ The input voltage must be 12V or higher |
||||
|
Consumption power |
240mW(12V, 20mA or less) |
||||
|
Temperature |
In storage |
-40℃ ~ 85℃ |
|||
|
In use
|
-25℃ ~ 50℃ |
||||
|
Humidity |
35% ~ 85% RH |
||||
|
Weight |
Max. 25g |
||||
|
Electrical wiring |
Grey[Power supply] and Yellow[Relay output] |
||||
※ Initial stabilization time: 10 seconds
※ These specifications may be changed without any prior notice.
※ The detection range may vary depending on the installation environment or conditions
External Appearance
Installation Steps
1. Drill 30Φ hole at the bottom of the engine box Locate hole position away from moving door parts
2, Insert sensor connection cable
3. Connect to controller
3. Connect to controller
5. Mount sensor panel
Align panel grooves parallel to glass door
Ensure panel surface is perpendicular to door & parallel to floor
Use double-sided tape if needed
Configuration
① Door Direction
② Detection Area Adjustment (Inner): Inner Zone Adjustment Window
③ Sensitivity Level Display
-1 (Lowest Sensitivity)
-5 (Highest Sensitivity)
④ Sensitivity Adjustment: Clockwise Rotation (Increase Sensitivity)
⑤ Detection Area Adjustment (Outer): Outer Zone Adjustment Window