Automatic Door Sensor
Exposed Type
Composite Sensor [GP301]
Integrated with sensing sensor and safety sensor
Key features
– Perfect side entry detection
– Top flush-mounted (integrated controller)
– Immunity to environmental interference (sunlight/ambient light/vibration)
– Adjustable closing stop time
– Adjustable external detection distance by raising sensor window while maintaining inner detection zone (Safety function included)
| Specifications | |||||
|---|---|---|---|---|---|
|
Detection method |
Far-infrared source |
||||
|
Installation height |
Below 3m |
||||
|
Detection range |
Left/Right |
1.2m[of the centerline]@ Height of 2.2m |
|||
|
Front/Rear |
(0.1 – [0.5~2.0])m @ Height of 2.2m |
||||
|
Normal |
DC 12V ~ 30V
※ The input voltage must be 12V or higher |
||||
|
Consumption power (output) |
240mW(12V, 20mA) (Maximum 40V/700mA) |
||||
|
Temperature |
In storage |
-40℃ ~ 85℃ |
|||
|
In use |
-25℃ ~ 50℃ |
||||
|
Humidity |
35% ~ 85% RH |
||||
|
Weight |
Max. 80g |
||||
|
Electrical wiring |
Grey[Power supply] and Yellow[Relay output] |
||||
※ Initial stabilization time: 10 seconds
※ These specifications may be changed without any prior notice.
※ The detection range may vary depending on the installation environment or conditions
External Appearance
Installation Steps
① Attach the installation sticker to the front side of the engine box.
② Make wiring holes / fixed holes.
- A hole for the power/output connection
- Holes for fixing the lower case of the sensor
③ Route the wires and connect the sensor connector
④ Connect the Wiring Harness Connector
⑤ Fix the sensor
⑥ Secure the Upper Housing After Sensor Configuration
Configuration
Adjust sensitivity/closing stop time by rotating the variable resistor → Automatically switches to detection mode after 4 seconds.
| Setting | Range | Default |
|---|---|---|
|
Sensitivity |
Level 0 ~ 5 |
Level 3 |
|
Closing time |
0 ~ 5 sec |
3 sec |
※ The number of lit LEDs (0-5) indicates the current setting level, excluding the blinking LED at the bottom right
※ Default values are user-adjustable
Dedicated Safety Sensor [SP101]
For doors with existing automatic sensors, the SP101 can be easily added as a dedicated safety enhancement.
Key Features
– Simplified installation (no complex safety beam setup required)
– flush-mountable top housing (integrated controller)
– Immunity to environmental interference (sunlight/ambient light/vibration)
– Blind spot-free motion detection
| Specifications | |||||
|---|---|---|---|---|---|
|
Detection method |
Far-infrared source |
||||
|
Installation height |
Below 3m |
||||
|
Detection range |
Left/Right |
1.2m[of the centerline]@ Height of 2.2m |
|||
|
Front/Rear |
(0.1 – [0.5~2.0])m @ Height of 2.2m |
||||
|
Normal |
DC 12V ~ 30V ※ The input voltage must be 12V or higher |
||||
|
Consumption power (output) |
240mW(12V, 20mA) |
||||
|
Temperature |
In storage |
-40℃ ~ 85℃ |
|||
|
In use |
-25℃ ~ 50℃ |
||||
|
Humidity |
35% ~ 85% RH |
||||
|
Weight |
Max. 25g |
||||
|
Electrical wiring |
Grey[Power supply] and Yellow[Relay output] |
||||
※ Initial stabilization time: 10 seconds
※ These specifications may be changed without any prior notice.
※ The detection range may vary depending on the installation environment or conditions
External Appearance
Installation Steps
① Attach the installation sticker to the front side of the engine box.
② Make wiring holes / fixed holes.
- A hole for the power/output connection
- Holes for fixing the lower case of the sensor
③ Route the wires and connect the sensor connecto
④ Connect the Wiring Harness Connector
⑤ Fix the sensor
⑥ Secure the Upper Housing After Sensor Configuration
Configuration
| Setting | Range | Default |
|---|---|---|
|
Sensitivity |
Level 0 ~ 5 |
Level 3 |
|
Closing time |
0 ~ 5 sec |
3 sec |
※ The number of lit LEDs (0-5) indicates the current setting level, excluding the blinking LED at the bottom right
※ Default values are user-adjustable
Dedicated Safety Sensor [SP101]
For doors with existing automatic sensors, the SP101 can be easily added as a dedicated safety enhancement.
Key Features
– Simplified installation (no complex safety beam setup required)
– flush-mountable top housing (integrated controller)
– Immunity to environmental interference (sunlight/ambient light/vibration)
– Blind spot-free motion detection
| Specifications | |||||
|---|---|---|---|---|---|
|
Detection method |
Far-infrared source |
||||
|
Installation height |
Below 3m |
||||
|
Detection range |
Left/Right |
1.2m[of the centerline]@ Height of 2.2m |
|||
|
Front/Rear |
(0.1 – [0.5~2.0])m @ Height of 2.2m |
||||
|
Normal |
DC 12V ~ 30V ※ The input voltage must be 12V or higher |
||||
|
Consumption power (output) |
240mW(12V, 20mA) |
||||
|
Temperature |
In storage |
-40℃ ~ 85℃ |
|||
|
In use |
-25℃ ~ 50℃ |
||||
|
Humidity |
35% ~ 85% RH |
||||
|
Weight |
Max. 25g |
||||
|
Electrical wiring |
Grey[Power supply] and Yellow[Relay output] |
||||
※ Initial stabilization time: 10 seconds
※ These specifications may be changed without any prior notice.
※ The detection range may vary depending on the installation environment or conditions
External Appearance
Installation Steps
① Attach the installation sticker to the front side of the engine box.
② Make wiring holes / fixed holes.
- A hole for the power/output connection
- Holes for fixing the lower case of the sensor
③ Route the wires and connect the sensor connecto
④ Connect the Wiring Harness Connector
⑤ Fix the sensor
⑥ Secure the Upper Housing After Sensor Configuration
Configuration
Adjust sensitivity/closing stop time by rotating the variable resistor → Automatically switches to detection mode after 4 seconds.
| Setting | Range | Default |
|---|---|---|
|
Sensitivity |
Level 0 ~ 5 |
Level 3 |
|
Closing time |
0 ~ 5 sec |
3 sec |
※ The number of lit LEDs (0-5) indicates the current setting level, excluding the blinking LED at the bottom right
※ Default values are user-adjustable